RCD-RA1DA

Product feature

Attachment orientation

  • Catalogue (PDF)
  • User's manual PDF
  • 2 dimensional CAD drawing
  • Parametric CAD drawing
  • Request for information materials

    • Main specification

    HeadingContents
    LeadSliding screw lead (mm)2
    HorizontalLoad capacityMaximum load capacity (kg)0.7
    Speed/ Acceleration/DecelerationMaximum speed (mm/s)300
    Rated acceleration/deceleration (G)1
    Maximum acceleration/deceleration (G)1
    VerticalLoad capacityMaximum load capacity (kg)0.3
    Speed/ Acceleration/DecelerationMaximum speed (mm/s)300
    Rated acceleration/deceleration (G)1
    Maximum acceleration/deceleration (G)1
    ThrustRated thrust (N)4.2
    Pressing motionMax. pushing force (N)2.6
    Max. pushing speed (mm/s)5
    StrokeMinimum stroke (mm)10
    Maximum stroke (mm)30
    Stroke pitch (mm)10

    HeadingContents
    Drive systemSliding screw φ3mm　
    Accuracy of Repeating Positioning.±0.05mm
    Lost motion0.2mm and below
    Rodφ5mm Material: Stainless steel
    Non-rotational accuracy of rod±3.0°
    Allowable static torque at the rod tip0.02Nm
    Life time traveling distance10 million (round trip)
    Ambient operating temperature and humidityTemperature 0 - 40℃, Max 85% RH and below (no condensation)
    Protection gradeIP30
    Vibration resistant/Shock resistant4.9m/s2 100Hz and below
    Compatible to overseas standardsCE mark, RoHS compliant
    Motor typeDC Brushless motor
    Encoder typeIncremental
    Encoder pulse No.480 pulse/rev
    DeliveryWritten in [Reference for delivery] section of the homepage

    Stroke and maximum speed

    (Measured in mm/s)

    Lead (mm)10 - 30 (10mm interval)
    2300

    Current limit value and pressing force

    (Note) Pushing speed is 5mm/s.

    (Note) The graph above shows a range of value considering the drop in performance due to changes on sliding screw over time. Operate the equipment within the range between the lowest and the highest value shown.

    Adaptive controller

    The actuators introduced in this page are controllable using the controllers shown below. Please select their type based on intended usage.

    NameAppearanceMax. connectable
    axis No.    		Power source voltageControl methodMaximum positioning points
    PositionerPulse trainProgramNetwork ※Select
    DVCCPRCNMLML3ECEPPRTSSNECM
    DCON-CB/CGB1DC24V●
    ※Selectable    		●
    ※Selectable    		－●●●●●●●●●－－512
    DCON-CYB/PLB/POB1●
    ※Selectable    		●
    ※Selectable    		－－－－－－－－－－－－64
    MCON-C/CG8－－－●●●●－●●●●●●256
    MCON-LC/LCG6－－●●●●●－－●●●－－256
    RCM-P6DC1Applicable for RCP6S gateway system.768

    (Note) Please refer to page 6 -13 for abbreviated names of network (e.g. DV, CC).

    (Note) Simple absolute unit can't be used here.

    Oversea specification

    Important notes on selection

    (1) Load capacity assuming an acceleration of 1G. Acceleration upper limit is 1G.
    (2) Horizontal load capacity shown assumes an operation running with an external guide. Detent mechanism may get damaged if a force was applied to the rod, except towards its moving direction.
    (3) Due to sliding screw used in this device, main specification may change based on operating condition.
    (4) Please be aware that the rod moves downwards at turning off when used vertically, for this device has no brake equipped.
    (5) Please refer to page 1-427 for pressing motion.
    (6) Precaution is required depending on the attachment orientation. Please refer to page 1-379 for further information.

    Return to the page top

    Dimension drawing

    ST: Stroke

    M.E.: Mechanical end

    S.E.: Stroke end

    Dimension by stroke length

    Stroke102030
    L607080
    B526272

    Mass by stroke length

    Stroke102030
    Mass (kg)0.0470.0510.055